Jewelry MakingTOOLS

Manual tools. Working details. Informed choices.

Browse departments

JEWELRY MAKING TOOLS

Choose Looping Pliers, Mandrels, Jigs or a Coiler

Choose the forming size and the operation separately

The Beadsmith PLWE61 has six stated forming sizes: 2, 3, 4, 5, 7 and 9 mm. The Micro PL61T instead lists 1, 1.5, 2, 2.5, 3 and 4 mm. These are genuinely different size arrangements, including half-millimetre steps in the Micro; neither list is an evenly spaced generic 2–9 mm scale.

The Original One Step Looper offers a different operation: the selected version forms a 1.5 mm loop while trimming the wire. Its 24–18-gauge material/temper restrictions are separate from the loop size. Choose stepped forming jaws for several working positions, or the cut-and-loop mechanism when its specific loop and wire pairing match the job.

Use a mandrel for a continuous outline

The seven-piece MAN111 set provides oval, square, drop, rectangle, triangle, heart and star carbon-steel mandrels, approximately 3.5 inches long. Their tapered tips allow different size positions within each shape. Choose that set for the outline, not as seven measured round sizes.

The plastic MAN1000-1 gives twelve stepped round levels across 6.2–27.4 mm on a 7-inch tool, with a removable handle. It is the more relevant comparison when a round level and the ability to change the holding arrangement matter more than several geometric outlines. The individual steps are not all enumerated, so confirm a required exact level rather than assuming uniform increments.

Choose a winding system when the coil is the task

The EZ Coiler Pro COCO2 is selected as the nine-mandrel kit. Its contents include a mountable base, nine non-tapered round mandrels in 2–10 mm sizes, a chuck key, instructions and a zippered case. A collet and hand-operated handle change the working arrangement from free wrapping around a loose mandrel.

COCO-OV is a separate accessory: three oval mandrels in 4×6, 5×7 and 6×8 mm cross-sections. It is not a second complete coiler and those three oval rods are not the round mandrels in COCO2. Confirm the exact receiving coiler and wire requirement; the material names in the descriptions do not provide a universal gauge or temper limit.

Use a peg jig for a path rather than one shape

The Wig Jig Cyclops offers 385 holes and ten removable metal pegs in a 5-inch radial acrylic layout. Its transparent base can sit over a pattern for tracing. That is useful when the wire must follow several points, rather than one continuous mandrel surface or a single cut-and-loop motion.

Compare the working geometry with the component you intend to make: a radial peg layout, a tapered shape, a fixed step and a winding mandrel are not interchangeable merely because all can form wire. Tool diameter is the forming surface; wire and construction still affect the finished part. Keep exact interface and supplied-parts checks beside the size comparison, especially for coiler accessories.

Questions before choosing

I need a 6 mm forming position. Does the 2–9 mm PLWE61 list it?

Its stated positions are 2, 3, 4, 5, 7 and 9 mm. A 6 mm position is not listed, so do not buy it for that exact requirement without confirmation.

I already have COCO2. What adds an oval cross-section?

The COCO-OV accessory lists 4×6, 5×7 and 6×8 mm oval mandrels for EZ Coiler Pro; confirm the exact receiving setup rather than buying another round kit.

Which example should I compare for a heart-shaped outline?

MAN111 includes a heart mandrel among its seven shapes. The stepped MAN1000-1 is round and does not provide that outline.

Which tool suits a repeated path around several points?

The Cyclops radial jig positions removable pegs over a pattern. A single mandrel supplies one continuous surface rather than the same multi-point path.

Manufacturer references

Put this guide in context

See all 17 linked product dossiers

Check each model’s dimensions and fitting requirements when choosing equipment to use together.